T05 active magnetoelectric speed sensor
Using the Hall effect principle, when the metal tooth passes through the front end of the Hall sensor, the magnetic field changes, the Hall element detects the magnetic field change, and converts it into an alternating electric signal. The built-in circuit of the sensor amplifies and shapes the signal, and the output is good. Rectangular pulse signal, measuring frequency range is wider, can measure 0 speed, output signal is more accurate and stable, and easy to install, widely used in vehicle, motor, fan, steam turbine speed measurement.
Technical Parameters:
1 Working voltage: DC5～30V
2 Measuring range: 0～20KHz
3 Speed ​​measuring gear form: modulus 1 ~ 3 (involute gear)
4 output signal: square wave, its peak-to-peak value is approximately equal to the operating power supply voltage amplitude, independent of the speed
5 Working temperature: -30 ~ +120 ° C
6 Thread size: M16×1×80mm or M12×1×80mm (can be customized)
7 Installation clearance: 1~5mm
8 Weight: about 100 g
T05 active magnetoelectric speed sensor
I. Overview: XS12JK series magnetoelectric speed sensor,
The angular displacement can be converted into an electrical signal for the counter to count,
As long as it is non-contact, it can measure various magnetic conductive materials such as gears, impellers, and the speed of the disk with holes (or slots, screws) and the linear velocity.
One: The sensor has the advantages of small volume, strong and reliable, long life, no need of power supply and lubricating oil, etc., and can be used with general secondary instruments.
Second, the technical parameters: 1, the output waveform: approximate sine wave (≥ 50r / min)
2. Output signal amplitude: ≥300mv sensor at 50r/min
The core and the measured gear tip clearance δ=0.5～1.2mm The measured gear module m=2
Gear Z = 60
Magnetoelectric Magnetic Sensing Reluctance Hall Type Rotating Speed ​​Probe Speed ​​Sensor
Material The amplitude of the electrical steel signal is proportional to the speed and inversely proportional to the size of the core and the tip clearance.
3, measuring range: 50 ~ 5000Hz4, use time: continuous use
5, working environment: temperature -20 ~ +60 ° C -20 ~ +160 ° C (special custom
) 6, output form: X12K4P four-pin plug
7. Dimensions: outer diameter M16×1; M18×1.5 total length 80mm, can be customized according to requirements.
8, weight: about 120g (excluding the output wire) Third, the outline drawing: Fourth, the use of precautions: 1, the sensor housing M16 × 1 thread must not be damaged, hex nut rotation should be free, after the hex nut is tight, no loose phenomenon. 2. It is advisable to install the gear to be tested without contact with the sensor. It is hoped that the gap δ can be minimized to increase the amplitude of the output signal. Five, single machine set:
1. XS12JK magnetoelectric speed sensor 1
2, X12K4P plug 1 only 3, manual 1 copy
4. Certificate 1
ZH2051 programmable speed impact sub-monitor instrument ZH2052 programmable speed monitor instrument ZH2054 programmable zero speed monitor instrument ZH2056 programmable anti-speed monitor instrument ZH2062 programmable eccentricity monitor instrument ZH2072 programmable displacement monitor instrument
BSQ series transmitter introduction BSQ001 power converter BSQ011 series vibration transmitter BSQ021 series shaft vibration transmitter BSQ031 series axial displacement transmitter BSQ051 series speed transmitter BSQ073 series stroke transmitter BS series installation box
YZHS/YZHV/YZH-S/YZH-V series integrated vibration bit transmitter YZH-B integrated vibration transmitter YZH-K series electronic vibration switch ZDT-2 portable vibration checker ZST-1 speed calibration Taiwan 8400 Series Static Calibrator Instrument ZY-350 Dynamic Calibrator Instrument
DWQZ series eddy current sensor SZ-4 type magnetoelectric speed sensor SZ-6 (C) type magnetoelectric speed sensor SZ-6B type magnetoelectric speed sensor SZ-6i type explosion-proof magnetic type speed sensor ZHS-9/ZHV -9 integrated ultra-low frequency vibration displacement sensor SMCB-01/02 magnetic sensitive speed sensor SZCB series magnetoresistive Hall gear speed sensor speed sensor TD series LVDT sensor UT-81 series LVDT sensor B49 (UHZ) series magnetic flip column liquid Position sensor SZCB-01i type explosion-proof reluctance type speed sensor SZ-6i type explosion-proof magnetic type speed sensor TD-1i type LVDT sensor Hall gear speed sensor
CWY-DO eddy current sensor probe front-end device CWY-DO810030 eddy current sensor extension cable TRLS-9 low-frequency vibration speed sensor TRLV-9200 vibration speed sensor TRLV-hall gear speed sensor 9268 vibration speed sensor TRLV-8 vibration speed sensor GA- GT-61 accelerometer
Using the Hall effect principle, when the metal tooth passes through the front end of the Hall sensor, the magnetic field changes, the Hall element detects the magnetic field change, and converts it into an alternating electric signal. The built-in circuit of the sensor amplifies and shapes the signal, and the output is good. Rectangular pulse signal, measuring frequency range is wider, can measure 0 speed, output signal is more accurate and stable, and easy to install, widely used in vehicle, motor, fan, steam turbine speed measurement.
Technical Parameters:
1 Working voltage: DC5～30V
2 Measuring range: 0～20KHz
3 Speed ​​measuring gear form: modulus 1 ~ 3 (involute gear)
4 output signal: square wave, its peak-to-peak value is approximately equal to the operating power supply voltage amplitude, independent of the speed
5 Working temperature: -30 ~ +120 ° C
6 Thread size: M16×1×80mm or M12×1×80mm (can be customized)
7 Installation clearance: 1~5mm
8 Weight: about 100 g
T05 active magnetoelectric speed sensor
I. Overview: XS12JK series magnetoelectric speed sensor,
The angular displacement can be converted into an electrical signal for the counter to count,
As long as it is non-contact, it can measure various magnetic conductive materials such as gears, impellers, and the speed of the disk with holes (or slots, screws) and the linear velocity.
One: The sensor has the advantages of small volume, strong and reliable, long life, no need of power supply and lubricating oil, etc., and can be used with general secondary instruments.
Second, the technical parameters: 1, the output waveform: approximate sine wave (≥ 50r / min)
2. Output signal amplitude: ≥300mv sensor at 50r/min
The core and the measured gear tip clearance δ=0.5～1.2mm The measured gear module m=2
Gear Z = 60
Magnetoelectric Magnetic Sensing Reluctance Hall Type Rotating Speed ​​Probe Speed ​​Sensor
Material The amplitude of the electrical steel signal is proportional to the speed and inversely proportional to the size of the core and the tip clearance.
3, measuring range: 50 ~ 5000Hz4, use time: continuous use
5, working environment: temperature -20 ~ +60 ° C -20 ~ +160 ° C (special custom
) 6, output form: X12K4P four-pin plug
7. Dimensions: outer diameter M16×1; M18×1.5 total length 80mm, can be customized according to requirements.
8, weight: about 120g (excluding the output wire) Third, the outline drawing: Fourth, the use of precautions: 1, the sensor housing M16 × 1 thread must not be damaged, hex nut rotation should be free, after the hex nut is tight, no loose phenomenon. 2. It is advisable to install the gear to be tested without contact with the sensor. It is hoped that the gap δ can be minimized to increase the amplitude of the output signal. Five, single machine set:
1. XS12JK magnetoelectric speed sensor 1
2, X12K4P plug 1 only 3, manual 1 copy
4. Certificate 1
ZH2051 programmable speed impact sub-monitor instrument ZH2052 programmable speed monitor instrument ZH2054 programmable zero speed monitor instrument ZH2056 programmable anti-speed monitor instrument ZH2062 programmable eccentricity monitor instrument ZH2072 programmable displacement monitor instrument
BSQ series transmitter introduction BSQ001 power converter BSQ011 series vibration transmitter BSQ021 series shaft vibration transmitter BSQ031 series axial displacement transmitter BSQ051 series speed transmitter BSQ073 series stroke transmitter BS series installation box
YZHS/YZHV/YZH-S/YZH-V series integrated vibration bit transmitter YZH-B integrated vibration transmitter YZH-K series electronic vibration switch ZDT-2 portable vibration checker ZST-1 speed calibration Taiwan 8400 Series Static Calibrator Instrument ZY-350 Dynamic Calibrator Instrument
DWQZ series eddy current sensor SZ-4 type magnetoelectric speed sensor SZ-6 (C) type magnetoelectric speed sensor SZ-6B type magnetoelectric speed sensor SZ-6i type explosion-proof magnetic type speed sensor ZHS-9/ZHV -9 integrated ultra-low frequency vibration displacement sensor SMCB-01/02 magnetic sensitive speed sensor SZCB series magnetoresistive Hall gear speed sensor speed sensor TD series LVDT sensor UT-81 series LVDT sensor B49 (UHZ) series magnetic flip column liquid Position sensor SZCB-01i type explosion-proof reluctance type speed sensor SZ-6i type explosion-proof magnetic type speed sensor TD-1i type LVDT sensor Hall gear speed sensor
CWY-DO eddy current sensor probe front-end device CWY-DO810030 eddy current sensor extension cable TRLS-9 low-frequency vibration speed sensor TRLV-9200 vibration speed sensor TRLV-hall gear speed sensor 9268 vibration speed sensor TRLV-8 vibration speed sensor GA- GT-61 accelerometer
Coffee Capsule,Capsule Cup,Coffee Capsule Cup,Plastic Coffee Capsule Cup
Jiangsu Fantasy Packaging New Material Co., Ltd. , https://www.jiangsufantasypack.com